In the reduced order modeling (ROM) framework, the solution of a parametric partial differential equation is approximated by combining the high-fidelity solutions of the problem at hand for several properly chosen configurations. Examples of the ROM application, in the naval field, can be found in [31, 24]. Mandatory ingredient for the ROM methods is the relation between the high-fidelity solutions and the parameters. Dealing with geometrical parameters, especially in the industrial context, this relation may be unknown and not trivial (simulations over hand morphed geometries) or very complex (high number of parameters or many nested morphing techniques). To overcome these scenarios, we propose in this contribution an efficient and complete data-driven framework involving ROM techniques for shape design and optimization, extending the pipeline presented in [7]. By applying the singular value decomposition (SVD) to the points coordinates defining the hull geometry –- assuming the topology is inaltered by the deformation –-, we are able to compute the optimal space which the deformed geometries belong to, hence using the modal coefficients as the new parameters we can reconstruct the parametric formulation of the domain. Finally the output of interest is approximated using the proper orthogonal decomposition with interpolation technique. To conclude, we apply this framework to a naval shape design problem where the bulbous bow is morphed to reduce the total resistance of the ship advancing in calm water.

%B VIII International Conference on Computational Methods in Marine Engineering %G eng %U https://arxiv.org/abs/1905.05982 %0 Conference Paper %B VIII International Conference on Computational Methods in Marine Engineering %D 2019 %T Efficient Reduction in Shape Parameter Space Dimension for Ship Propeller Blade Design %A Mola, Andrea %A Tezzele, Marco %A Gadalla, Mahmoud %A Valdenazzi, Federica %A Grassi, Davide %A Padovan, Roberta %A Rozza, Gianluigi %XIn this work, we present the results of a ship propeller design optimization campaign carried out in the framework of the research project PRELICA, funded by the Friuli Venezia Giulia regional government. The main idea of this work is to operate on a multidisciplinary level to identify propeller shapes that lead to reduced tip vortex-induced pressure and increased efficiency without altering the thrust. First, a specific tool for the bottom-up construction of parameterized propeller blade geometries has been developed. The algorithm proposed operates with a user defined number of arbitrary shaped or NACA airfoil sections, and employs arbitrary degree NURBS to represent the chord, pitch, skew and rake distribution as a function of the blade radial coordinate. The control points of such curves have been modified to generate, in a fully automated way, a family of blade geometries depending on as many as 20 shape parameters. Such geometries have then been used to carry out potential flow simulations with the Boundary Element Method based software PROCAL. Given the high number of parameters considered, such a preliminary stage allowed for a fast evaluation of the performance of several hundreds of shapes. In addition, the data obtained from the potential flow simulation allowed for the application of a parameter space reduction methodology based on active subspaces (AS) property, which suggested that the main propeller performance indices are, at a first but rather accurate approximation, only depending on a single parameter which is a linear combination of all the original geometric ones. AS analysis has also been used to carry out a constrained optimization exploiting response surface method in the reduced parameter space, and a sensitivity analysis based on such surrogate model. The few selected shapes were finally used to set up high fidelity RANS simulations and select an optimal shape.

%B VIII International Conference on Computational Methods in Marine Engineering %G eng %U https://arxiv.org/abs/1905.09815 %0 Conference Paper %B VIII International Conference on Computational Methods in Marine Engineering %D 2019 %T Shape optimization through proper orthogonal decomposition with interpolation and dynamic mode decomposition enhanced by active subspaces %A Tezzele, Marco %A Demo, Nicola %A Rozza, Gianluigi %XWe propose a numerical pipeline for shape optimization in naval engineering involving two different non-intrusive reduced order method (ROM) techniques. Such methods are proper orthogonal decomposition with interpolation (PODI) and dynamic mode decomposition (DMD). The ROM proposed will be enhanced by active subspaces (AS) as a pre-processing tool that reduce the parameter space dimension and suggest better sampling of the input space. We will focus on geometrical parameters describing the perturbation of a reference bulbous bow through the free form deformation (FFD) technique. The ROM are based on a finite volume method (FV) to simulate the multi-phase incompressible flow around the deformed hulls. In previous works we studied the reduction of the parameter space in naval engineering through AS [38, 10] focusing on different parts of the hull. PODI and DMD have been employed for the study of fast and reliable shape optimization cycles on a bulbous bow in [9]. The novelty of this work is the simultaneous reduction of both the input parameter space and the output fields of interest. In particular AS will be trained computing the total drag resistance of a hull advancing in calm water and its gradients with respect to the input parameters. DMD will improve the performance of each simulation of the campaign using only few snapshots of the solution fields in order to predict the regime state of the system. Finally PODI will interpolate the coefficients of the POD decomposition of the output fields for a fast approximation of all the fields at new untried parameters given by the optimization algorithm. This will result in a non-intrusive data-driven numerical optimization pipeline completely independent with respect to the full order solver used and it can be easily incorporated into existing numerical pipelines, from the reference CAD to the optimal shape.

%B VIII International Conference on Computational Methods in Marine Engineering %G eng %U https://arxiv.org/abs/1905.05483